Product category:
Weighing and balancing
News Release from: CI Electronics | Subject: Microbalance head
Edited by the Laboratorytalk Editorial
Team on 02 October 2007
Upgrade of Faraday balance susceptometer
in Zagreb
Faraday balance susceptometers work on the principle that applying a vertical magnetic field gradient to a sample adds to or subtracts from its weight
Scientists at the Rudjer Boskovic Institute in Zagreb, Croatia, have purchased a microbalance head, control unit, software and accessories from CI Electronics to upgrade a Faraday balance susceptometer used to investigate the magnetic susceptibility of various materials Compared with alternatives, the CI microbalance head was less expensive, yet it still met the required specification for sensitivity and operation in a vacuum, plus CI Electronics was able to supply only the components and accessories required to enable the scientists to retrofit them to the existing apparatus
This article was originally published on Laboratorytalk on 18 Oct 2005 at 8.00am (UK)
Related stories
Microbalances worth their weight in gold
Analytical instrument manufacturer provides solid endorsement of the value of these microbalance heads in its range of instruments for surface chemistry and materials science
Microbalance crucial in material thermal analysis
Researchers at Instituto de Ciencia de Materiales de Sevilla analyse the kinetics of solid state reactions by heating (or cooling) a sample and plotting its weight as a function of time or temperature
The complex compounds laboratory within the division of materials chemistry at the Rudjer Boskovic Institute has a Faraday balance susceptometer that was designed and constructed in-house a number of years ago.
However, the scientists wanted to improve the performance of the apparatus and the existing microbalance head was not straightforward to integrate with modern PC-based control systems.
The supplier was unable to provide the level of technical support required, so Berislav Peric, an associate in the laboratory, turned to CI Electronics.
Further reading
20 years experience with microbalance heads
For almost 20 years Zbigniew Grzesik has been using CI Electronics microbalance heads in the department of solid state chemistry at the AGH University of Science and Technology in Krakow, Poland
Compact benchtop weight sorter
Specifically designed for pharmaceutical research and development departments, it is said to be ideal for 100% weight sorting of small clinical trial batches
Water sorption analyser is improved
This fully automatic system is suitable for water sorption profiling of material samples including pharmaceuticals, foods, detergents, building materials, fibres, wood, and other substances
Following a series of email exchanges, Peric ordered an Mk2-M5 balance head with an aluminium enclosure, 5g capacity and 0.1ug resolution.
To complement this, a Disbal control unit was ordered, together with CI's LabWeigh for Windows software, a silica flask and various accessories.
All of this has now been incorporated within the Faraday balance susceptometer.
Peric comments: "CI Electronics was very helpful when we first enquired about the microbalance head, and we were able to specify the type of vacuum fittings to be installed beneath the balance head.
"In all respects the microbalance head and controller met our requirements, yet the price was much lower than we had been quoted by other suppliers".
By using a microbalance to quantify the magnetic force, the material's magnetic susceptibility can be calculated.
In the apparatus at the Rudjer Boskovic Institute, the sample hangs approximately 1m below the microbalance head on a quartz rod and is surrounded by low-temperature, low-pressure helium that transfers heat between the sample and the cryostat.
Readings are obtained from the microbalance head without the magnetic field applied; then, after one second, the magnetic field is applied and the sample weight is measured again for one second.
Although the upgraded cryostat has not yet been installed to control the sample temperature, the apparatus has been tested at room temperature and the microbalance head is performing as required.
An important aspect of the susceptometer upgrade was the ability to run experiments automatically under PC control.
Peric says: "With the CI LabWeigh for Windows software package, zeroing and calibrating the balance becomes very simple.
"CI Electronics also provides a small routine written in Visual Basic for easy communication between PC and balance.
"This routine can be combined with additional software usually used for control of another device such as Labview".
The alternative to upgrading the susceptometer was to purchase new specialist equipment such as a Squid (superconducting quantum interference devices) magnetometer.
Although this would offer very high sensitivity, the cost would have been far greater.
Peric concludes: "We believe the CI Electronics microbalance head and other hardware and software will help to improve and automate our magnetic susceptibility measurements.
"CI Electronics has been extremely helpful throughout the project, for which we are most grateful.".
• CI Electronics: contact details and other news
• Email this article to a colleague
• Register for the free Laboratorytalk email newsletter
• Laboratorytalk Home Page
Search the Pro-Talk network of sites
