Product category:
Mechanical testing equipment
News Release from: Flintec UK | Subject: CPB
Edited by the Laboratorytalk Editorial
Team on 13 November 2002
New concept in single point load cells
Instead of multiple load cells or a single cell and flexures, one dual or triple beam cantilever load cell is located centrally and the platform is secured directly to the top of the load cell
A new concept in single point load cells is set to bring significant changes to the design of low capacity weighing equipment The CPB aluminium planar beam from Flintec overcomes important design criteria which have hitherto not been addressed by load cell manufacturers
This article was originally published on Laboratorytalk on 15 Jan 2004 at 8.00am (UK)
Related stories
Mtec 2004 preview: ABB
ABB will be presenting the latest technology from its comprehensive range of instrumentation products and systems at Mtec 2004 (Birmingham NEC, 11-12 February 2004)
Radiometer probe measures UV or dental cure wands
Providing Nist traceable results, this radiometer is suitable for quality control by manufacturers who want to profile output uniformity over the wand's entire surface
The single point (or moment insensitive) load cell has been around for more than 30 years and is now well proven and accepted for use in bench scales, counting scales, postal scales, retail scales, checkout scales, medical scales, hopper scales, belt weighers - the list goes on.
Their design offers simpler scale design, elimination of flexures, high performance, wide range of capacities, low cost, and good environmental protection.
The principle of operation is very simple.
Further reading
Verification of phototherapeutic treatment levels
Hyperbilirubinemia monitor measures the output of the lamps used in phototherapy, before patient treatment takes place, to ensure accurate dosing
New possibilities for old HP mass spectrometers
Data acquisition system promises increased sensitivity and bandwidth and the ability to perform multiple experiments, breathing new life into old equipment
Vacuum gauge with integral controller
This family of low cost active vacuum gauge combines gauge head and controller in one small package
Instead of using multiple load cells (one at each corner) or a single load cell and flexures, one dual or triple beam cantilever load cell is located centrally in the scale and the platform or weighing structure is secured directly to the top of the load cell.
The design of this type of load cell resists torsional loads created by the load being placed off centre.
During manufacture, the flexures are manually adjusted by filing or grinding, in such a a way that wherever a load is placed on the platform, the output from the load cell remains the same.
Although the single point was originally designed for low capacity scales in relatively clean environments, developments in sealing technology, material of construction, and capacity range have significantly extended the use of this product.
Fully weld sealed IP68 stainless steel single point load cells up to 1000kg capacity are now available which can accommodate platform sizes of 1000 x 1000mm.
However,despite the developments in these areas, two important design criteria have, until now, eluded manufacturers.
Low capacity single points typically suffer from poor side to side stability and offer only a narrow mounting surface for the platform.
The flexures themselves are very thin, making the units susceptible to mechanical damage.
In parallel, attempts to design low profile products have floundered around a height of 20mm.
The design of the Flintec CPB not only provides an extremely low profile - down to less than 8mm for the 3-15kg versions - but also offers a very wide mounting surface.
The CPB has two flexures in the same horizontal plane, rather than above each other in the vertical plane.
The mounting surfaces between these flexures measure approximately 60 x 65mm and have four, rather than the customary two, fixing holes.
This provides a very stable base for fixing platforms, small hoppers, conveyors or other structures.
Even in the 3kg version, the CPB flexures give excellent mechanical strength and excellent side to side rigidity, allowing platform sizes of up to 350 x 350mm to be used.
These design criteria make the CPB particularly suitable for low profile bench scales, checkout scales, baby scales and postal scales, as well as small hopper scales and filling machines.
• Flintec UK: contact details and other news
• Email this article to a colleague
• Register for the free Laboratorytalk email newsletter
• Laboratorytalk Home Page
Search the Pro-Talk network of sites
