Product category:
Gas analysis equipment
News Release from: Michell Instruments | Subject: Easidew On-Line
Edited by the Laboratorytalk Editorial
Team on 29 November 2006
Dewpoint measurement of medical gases
HTM02 update
Health Technical Memorandum (HTM) 02 is one in a series published by the UK National Health Service Executive (NHSE) providing guidance on healthcare standards, policies, and established best practice
HTM 02 covers the subject of medical gas systems HTM 02 is divided in two parts: part A deals with design, installation and validation, while part B deals with operational management
This article was originally published on Laboratorytalk on 14 Dec 2005 at 8.00am (UK)
Related stories
Making dew point measurement simple
The Easidew On-line offers affordable and simple dew-point measurement and is designed to make continuous measurement of the dew point in compressed air and industrial gases reilable and accurate
New applications for cooled mirror dew point meter
The Optidew cooled mirror dew point meter offered by Michell Instruments can now be used for a wide variety of applications due to its increased cable length of up to 250 metres
The overall aim is to provide a safe, convenient and cost effective system for the provision of medical gases to the clinical and nursing staff at the point of use.
For the first time HTM regulations give specific information on the specification and measurement of dewpoint or moisture content.
The relevant section states:-.
Further reading
Humidity measurement: accurate, stable, repeatable
The Probe Connector series (PC series) is the latest range of relative humidity (RH) products developed by Michell's associated company, Rense, and provides a solution for many applications
Moisture measurement slide rule calculator is free
This useful tool also includes practical definitions and equations such as the equation for ppmv and the way of calculating a given saturation vapour pressure
Humidity measurement for engine development
The measurement of humidity plays an important role in measuring the efficiency, power output and emissions of internal combustion engines
15.146 "The plant test point and a representative sample of terminal units distributed throughout the pipeline systems should be tested for total water content.
"The water content must not exceed 67vpm (equivalent to an atmospheric pressure dew-point of approximately -46C).
"The typical water content of medical gas cylinders is normally below 5vpm.
"Water vapour content may be measured using the appropriate test device described in Appendix E (see also paragraph 15.117)".
While paragraph 15.117 tells us:-.
15.117 "An electronic dew-point meter should be used in preference to water content measurements".
More details are given in paragraph 7.41.
7.41 "The dryer control system should ensure that regeneration is operated in proportion to the compressed air usage.
"The effectiveness of the control system will become apparent when the efficiency of the compressor system is tested at 10% and 0% of the system design flow.
"Evidence of the reliability and performance of a dryer system should be sought from manufacturers, since these items are critical to the overall performance of the compressor system.
"The dryer control system should include a dew-point hygrometer and display with a minimum accuracy of +/-3C in a range from -20 C to -60C atmospheric dew-point, with an alarm set point of -46C (Note that this supersedes the HTM 2022 requirement for an alarm trigger point of 40 C).
"It should be arranged that in the event of open circuit, a 'plant emergency' alarm be initiated".
Michell Instruments has in the past been active in supplying portable equipment such as the Cermax portable dewpointmeter.
More than 40 instruments have been supplied within the UK, many with sampling systems to allow quick and easy connection to medical gas supplies within hospitals and pharmacies.
Michell Instruments says it has been quick off the mark regarding continuous measurement, and has already received orders from several customers for this application.
Where continuous measurement of dewpoint is required Michell Instruments says it has the ideal instrument: Easidew On-Line.
The Easidew On-Line utilises the Michell Instruments ceramic sensor to provide stable and accurate measurement of dewpoint in the range of -100 to + 20C.
The Easidew On-Line monitor provides a large red LED display of the dewpoint.
A 4-20mA analogue output is available for interfacing to data-loggers or distributed control system, and two alarms relays can be set by the user to provide indication that the gas is approaching, or is outside, the required specification.
To provide a one-stop service to the customer Michell Instruments can, if required, provide the Easidew On-Line already mounted within wall-mounted enclosure, and with a sampling system.
This sampling system includes a filter, to protect the sensor, and a valve and flowmeter so that the appropriate sample flowrate can be set.
This all in one approach requires only that the customer provide a flow of gas and the necessary pipework.
This solution is particularly useful for fitting to existing medical gas dryers.
Easidew On-Line is described as the perfect solution for new medical gas systems or for those users with older systems wishing to ensure that they meet the new HTM 02 standards. Request a free brochure from Michell Instruments ...
• Michell Instruments: contact details and other news
• Email this article to a colleague
• Register for the free Laboratorytalk email newsletter
• Laboratorytalk Home Page
Search the Pro-Talk network of sites
